NorbertB

Forum Replies Created

Viewing 14 posts - 1 through 14 (of 14 total)
  • 12. Januar 2020 at 20:19 #47919

    Moin The1ne,

    meine Lautsprecherkabel sind bis zu ca. 30 Meter lang (verlegt in Leerrohren).
    Und nein, weitere Dienste laufen nicht auf den Raspis. Ich benutze sie ausschliesslich zur Beschallung (Logitech-Media-Server und Squeezelight als Player).

    Gruß,
    Norbert

    3. Oktober 2019 at 19:17 #47226

    Nachdem ich vor 4 Wochen auf einzelne Netzteile umgerüstet habe, läuft die gesamte Installation ohne jegliche Ausfälle 🙂

    6. September 2019 at 15:06 #47017

    Hallo Heiner,

    vielen Dank für Deine Tips. Bei Hifiberry rät man davon ab mehrere Devices über ein gemeinsames Netzteil zu versorgen, siehe dortiger Beitrag. Deine Vermutung war also richtig.
    Ich werde das jetzt mal umbauen.

    Vielen Dank nochmal! 🙂

    • This reply was modified 4 years, 7 months ago by NorbertB.
    3. September 2019 at 19:15 #46969

    Ja, ich habe noch andere Netzteile und werde das probieren.
    Was spricht aber gegen ein zentrales Netzteil im Allgemeinen und gegen das Meanwell-Netzteil im Speziellen?
    Die Stromversorgung vom Netzteil geht auf Reihenklemmen und von dort jeweils zum Amp.

    • This reply was modified 4 years, 8 months ago by NorbertB.
    3. September 2019 at 11:45 #46966

    Hallo Heiner,

    Die Lüfter ziehen den Strom vom Pi (Pin 4 + 6), die Pi’s sind 3B+.
    Das gemeinsame Netzteil für alle 10 Systeme ist ein Meanwell MW RSP-1000-15, mit 15V und 50A.
    Die SD-Karten habe ich vor einiger Zeit mal durch USB-Sticks ersetzt, da mir der Dauerbetrieb über SD-Karten zu unsicher erschien (hohe Ausfallrate der SD-Cards). Ein Schreibschutz-Plugin ist nicht im Einsatz, die Systeme werden routinemäßig nicht vom Strom getrennt, sie laufen durch.

    Danke und Gruß,
    Norbert

    29. Juli 2019 at 18:55 #46525

    OK, I think, I know the reason for this. By copying the SD card to the SSD device, the UUID will be inherited.
    If I change something on partition table, the UUID will be overwritten.
    I’ve adjusted this on cmdline.txt but this solves not my problem completely. Raspi starts booting, but I get lots of errors beginning by „failed to start remount of root and kernel file system“

    29. Juli 2019 at 18:15 #46523

    I tried diffrent things, but nothing is working…

    – First I’ve maked a 1:1 copy of the SD card to the SSD by using a Linux dd (plugged by using a SATA to USB adaptor) – this is working well.
    – Then I created a third partition (ext4) by using an ubuntu laptop – Raspi doesn’t boot anymore
    – Now I’ve maked a new copy from SD card to SSD and booted the Raspi. On console of my Pi I’ve maked a new partition by using cfdisk – reboot goes wrong.
    – At third, I’ve maked a new copy again and booted the Pi well. Then, I’ve increased the existing ext4 partition and tried to boot the Raspi – no way…
    At last I’ve tried to disable boot device check at boot time by editing cmdline.txt: fsck.repair=no

    Nothing helps me to boot from SSD and using the full space of it…

    Does anyone have an idea?

    Thanks,
    Norbert

    28. Juli 2019 at 20:09 #46509

    Hello Heiner,

    no, I didn’t.
    I just wanted to bring the topic back into focus.

    Regards,
    Norbert

    9. Juli 2019 at 20:15 #46231

    It’s me again. Is anyone, maybe max2play, working on network boot?
    Could it be, that raspberry4 makes it more possible to find a running setup?

    Regards,
    Norbert

    23. Oktober 2018 at 12:50 #38791

    Any news about this topic?
    Is there a working network booted max2play possible in the meantime?

    Thanks,
    Norbert

    15. Juni 2018 at 10:36 #36205

    Ich habe für mich einen Trick gefunden um einen Mono-Speaker am AMP2 zu betreiben.
    Ich habe das Lautsprecher-Kabel an – des rechten Kanals und + des Linken Kanals angeschlossen.
    Damit bekomme ich einen aus beiden Kanälen gemixten output.
    Keine Ahnung ob diese Anschlussart supported ist, aber für mich funktioniert es so.

    9. Juni 2018 at 17:18 #36133

    Hallo Heiner,

    ich habe hier die neuen RPi3B+ mit Hifi Berry Amp2 im Einsatz.
    Hier helfen mir die Hinweise in dem von Dir referenzierten Beitrag leider nicht weiter.
    Ich bekomme die Einstellungen für Mono nicht hin 🙁

    Meine Einstellungen:
    /etc/asound.conf:

    ctl.!default {
        type hw
        card 0
    }
    pcm.equal {
        type plug;
        slave.pcm plugequal;
    }
    ctl.equal {
       type equal;
       module "Eq10";
    }
    
    pcm.plugequal {
       type equal;
       module "Eq10";
       slave {
         pcm "plughw:0,0";
       }
       hint {show on;description "Equalizer for plughw:0,0"}
    }
    
    pcm.mono {
         type route
         slave.pcm equal
         slave.channels 2
         ttable.0.0 0.5    # L(0) to L(0) at 0.5 volume
         ttable.1.0 0.5    # R(1) to L(0) at 0.5 volume
         ttable.0.1 0.5    # L(0) to R(1) at 0.5 Volume
         ttable.1.1 0.5    # R(1) to R(1) at 0.5 Volume
    }
    

    /opt/max2play/audioplayer.conf:

    ### Configuration of Audioplayers
    SQUEEZELITE_PARAMETER=-o sysdefault:CARD=sndrpihifiberry -a 80:4:: -o mono
    SQUEEZESLAVE_PARAMETER=-n plugequal
    SHAIRPORT_PARAMETER=-d default:CARD=sndrpihifiberry -t hardware -m hw:1 -c Digital
    USE_USB_DAC=0
    USE_EQUALIZER=1
    SYSTEM_USER=pi
    YMPD_PARAMETER=--webport 8081
    

    Kann mir da jemand einen Tip geben?

    Danke vorab!
    Norbert

    • This reply was modified 5 years, 10 months ago by NorbertB.
    • This reply was modified 5 years, 10 months ago by NorbertB.
    22. Februar 2017 at 13:35 #27120

    OK, thanks!
    In my environment it also was card 1.
    Now its working well 🙂

    21. Februar 2017 at 20:51 #27098

    Sorry for hijacking this thread.
    My problem is the same as decribed below.
    I’m using AMP+ Card and no Equalizer is working.
    In advanced setting soundcard is set to „“sysdefault – snd_rpi_hifiberry_amp, Default Audio Device, sndrpihifiberry“.
    If I set this to “plugequal – Equalizer for plughw:0,0” no sound is hearable anymore.
    What do I have to do for make Equalizer working with HiFiBerry AMP+?

Viewing 14 posts - 1 through 14 (of 14 total)