Aylon

Forum Replies Created

Viewing 4 posts - 1 through 4 (of 4 total)
  • Posted in:
  • 10. Mai 2018 at 20:48 #35648

    Hi Heiner,

    Used the fathersday to start from scratch again and this time with another RPi i still had flying around. While at first I had the same issue with the bluetooth streaming it is now working.

    Seems as if the bluetooth streaming uses always the device #1 even if the on board sound is disabled and the AMP2 being at device #0 position.

    However, my AMP2 somehow did not play via squeezlite first when on-board sound is not disabled and the card is #1. So I disabled on-board sound change hw:1 to hw:0 with the audioplayer and it played well. Bluetooth however not at this time. I the enabled on-board sound again and magically both, bluetooth and audioplayer worked well.

    Strange but at the moment it is solved for now.

    Many thanks,
    Aylon

    9. Mai 2018 at 23:51 #35641

    Hi Heiner,

    Thanks again but that unfortunately did not change it.

    Tried following:
    – enabled on-board sound & changes sqeezlite audioplayer [SL] to hw:0 = music from SL works fine but no sound via BT streaming
    – added the dmix option = SL works fine but no sound via BT
    – tried all three soundcard options on BT site = no soud via BT

    last I upgraded kernel + updated all packages but still the Problem persists? I do not get any sound via BT streaming option?

    anything else maybe to test or see what might be the case? I can SSH into the RPi if that would add any value with the right commands?

    Thanks again
    Aylon

    8. Mai 2018 at 23:30 #35608

    Strangely did my previous reply just disappear … hence here the details again.

    Shairport & DNLA were both already disabled.

    From the DEBUG I wonder if the following is simply incorrect as I disabled on-board sound?

    BLUEALSA_PLAY_AUDIOCARD=hw:1,0

    should actually be

    BLUEALSA_PLAY_AUDIOCARD=hw:0,0

    If so, how do I change this value as I have only one option on the bluetooth streaming section and this one is chosen:

    sndrpihifiberry – hw:0:0 – Mixer Digital – HiFiBerry DAC+ HiFi pcm512x-hifi-0 []

    Full DEBUG output below and again many thanks for your help!

    #### SQUEEZELITE VERSION ####
    Squeezelite Max2Play v1.0.2 based on v1.8.4-726, Copyright 2012-2015 Adrian Smith, 2015-2016 Ralph Irving.

    #### SQUEEZELITE BUILDOPTIONS ####
    Build options: LINUX ALSA EVENTFD RESAMPLE FFMPEG VISEXPORT IR GPIO DSD CONTROLSBS ALSASYNC BLUETOOTHSYNC

    #### AUDIOPLAYER CONFIG ####
    ### Configuration of Audioplayers
    SQUEEZELITE_PARAMETER=-o sysdefault:CARD=sndrpihifiberry -a 80:4:: -o hw:0 -V Digital -C 5
    SQUEEZESLAVE_PARAMETER=-n plugequal
    SHAIRPORT_PARAMETER=-d default:CARD=sndrpihifiberry -t hardware -m hw:1 -c Digital
    USE_USB_DAC=0
    USE_EQUALIZER=0
    SYSTEM_USER=pi
    YMPD_PARAMETER=–webport 8081
    BLUEALSA_PLAY_AUDIOCARD=hw:1,0
    BLUEALSA_PLAY_MIXER=Digital

    #### SQUEEZELITE -l ####
    Output devices:
    null – Discard all samples (playback) or generate zero samples (capture)
    equal
    plugequal – Equalizer for plughw:0,0
    bluetooth – Your Bluetooth device 88:AD:D2:1C:C1:04
    default:CARD=sndrpihifiberry – snd_rpi_hifiberry_dacplus, – Default Audio Device
    sysdefault:CARD=sndrpihifiberry – snd_rpi_hifiberry_dacplus, – Default Audio Device
    dmix:CARD=sndrpihifiberry,DEV=0 – snd_rpi_hifiberry_dacplus, – Direct sample mixing device
    dsnoop:CARD=sndrpihifiberry,DEV=0 – snd_rpi_hifiberry_dacplus, – Direct sample snooping device
    hw:CARD=sndrpihifiberry,DEV=0 – snd_rpi_hifiberry_dacplus, – Direct hardware device without any conversions
    plughw:CARD=sndrpihifiberry,DEV=0 – snd_rpi_hifiberry_dacplus, – Hardware device with all software conversions

    #### SHAIRPORT (SYNC) VERSION ####
    3.1.1-OpenSSL-Avahi-ALSA-soxr-sysconfdir:/usr/local/etc

    #### OUTPUT SOUND DETAILS CARD 0 ####
    closed

    #### OUTPUT SOUND DETAILS CARD 1 ####

    8. Mai 2018 at 13:49 #35591

    Hi Heiner,

    Many thanks for the reply but the flag is already set in my previous testing.

    So this seems not to cause the issues.

    Apologies for not mentioning it.

    Many thanks
    Aylon

Viewing 4 posts - 1 through 4 (of 4 total)