Reply To: Zugriff Weboberfläche

5. März 2019 at 15:22 #44660

Hallo Heiner,
mit „Prozess“ meinst Du den Zeitpunkt während des Bootens, nehme ich an? Bildschirm habe ich nn keinen angeschlossen, sondern stattdessn dmesg mittels ssh angeschaut. Dort schaut alles normal aus (hab‘ den Teil an Erkennung der Ethernet-Schnittstelle hier hineingepastet):

[ 2.066872] smsc95xx 1-1.1:1.0 eth0: register ’smsc95xx‘ at usb-20980000.usb-1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:12:7a:7b
[ 2.073651] NET: Registered protocol family 10
[ 2.076037] Segment Routing with IPv6
[ 2.092162] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 2.121355] random: systemd: uninitialized urandom read (16 bytes read)
[ 2.131712] systemd[1]: systemd 232 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN)
[ 2.133234] systemd[1]: Detected architecture arm.
[ 2.135048] systemd[1]: Set hostname to <Brain>.
[ 2.196651] random: systemd: uninitialized urandom read (16 bytes read)
[ 2.363098] usb 1-1.2: new high-speed USB device number 4 using dwc_otg
[ 2.495298] usb 1-1.2: New USB device found, idVendor=13fe, idProduct=5200
[ 2.495323] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2.495335] usb 1-1.2: Product: USB DISK 3.0
[ 2.495348] usb 1-1.2: Manufacturer:
[ 2.495357] usb 1-1.2: SerialNumber: 070056AEA0D50110
[ 2.496766] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[ 2.501730] random: systemd-sysv-ge: uninitialized urandom read (16 bytes read)
[ 2.504392] scsi host0: usb-storage 1-1.2:1.0
[ 2.583462] uart-pl011 20201000.serial: no DMA platform data
[ 2.603094] usb 1-1.3: new high-speed USB device number 5 using dwc_otg
[ 2.805041] usb 1-1.3: New USB device found, idVendor=1058, idProduct=0820
[ 2.805066] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=5
[ 2.805077] usb 1-1.3: Product: My Passport 0820
[ 2.805086] usb 1-1.3: Manufacturer: Western Digital
[ 2.805100] usb 1-1.3: SerialNumber: 575841314536343334345059
[ 2.806461] usb-storage 1-1.3:1.0: USB Mass Storage device detected
[ 2.810090] scsi host1: usb-storage 1-1.3:1.0
[ 3.504922] systemd[1]: Listening on Journal Socket.
[ 3.524756] scsi 0:0:0:0: Direct-Access USB DISK 3.0 PMAP PQ: 0 ANSI: 6
[ 3.532428] sd 0:0:0:0: [sda] 60566016 512-byte logical blocks: (31.0 GB/28.9 GiB)
[ 3.533091] sd 0:0:0:0: [sda] Write Protect is off
[ 3.533117] sd 0:0:0:0: [sda] Mode Sense: 2b 00 00 08
[ 3.533649] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn’t support DPO or FUA
[ 3.540967] systemd[1]: Listening on udev Control Socket.
[ 3.541911] systemd[1]: Listening on Journal Socket (/dev/log).
[ 3.544717] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[ 3.546945] systemd[1]: Created slice System Slice.
[ 3.555278] systemd[1]: Starting Create list of required static device nodes for the current kernel…
[ 3.558100] systemd[1]: Created slice system-systemd\x2dfsck.slice.
[ 3.786658] sda: sda1
[ 3.803872] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 3.844443] scsi 1:0:0:0: Direct-Access WD My Passport 0820 1012 PQ: 0 ANSI: 6
[ 3.849036] scsi 1:0:0:1: Enclosure WD SES Device 1012 PQ: 0 ANSI: 6
[ 3.853629] sd 1:0:0:0: [sdb] Spinning up disk…
[ 4.883072] .
[ 4.883527] ready
[ 4.884075] sd 1:0:0:0: [sdb] 3906963456 512-byte logical blocks: (2.00 TB/1.82 TiB)
[ 4.884905] sd 1:0:0:0: [sdb] Write Protect is off
[ 4.884932] sd 1:0:0:0: [sdb] Mode Sense: 47 00 10 08
[ 4.885748] sd 1:0:0:0: [sdb] No Caching mode page found
[ 4.891343] sd 1:0:0:0: [sdb] Assuming drive cache: write through
[ 5.086677] sdb: sdb1 sdb2 < sdb5 sdb6 sdb7 >
[ 5.093821] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 7.802429] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
[ 8.426537] systemd-journald[71]: Received request to flush runtime journal from PID 1
[ 9.109671] random: crng init done
[ 9.109700] random: 7 urandom warning(s) missed due to ratelimiting
[ 12.896383] snd-hifiberry-digi soc:sound: ASoC: CODEC DAI wm8804-spdif not registered – will retry
[ 12.917245] snd_bcm2835: module is from the staging directory, the quality is unknown, you have been warned.
[ 12.969754] bcm2835_alsa bcm2835_alsa: card created with 8 channels
[ 12.970301] snd-hifiberry-digi soc:sound: ASoC: CODEC DAI wm8804-spdif not registered – will retry
[ 17.739753] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 17.746374] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 17.770201] scsi 1:0:0:1: Attached scsi generic sg2 type 13
[ 19.745551] fuse init (API version 7.26)
[ 24.638718] Adding 102396k swap on /var/swap. Priority:-2 extents:1 across:102396k SSFS
[ 27.796296] smsc95xx 1-1.1:1.0 eth0: hardware isn’t capable of remote wakeup
[ 33.139463] input: lircd-uinput as /devices/virtual/input/input0
[ 36.517212] EXT4-fs (sdb5): mounted filesystem with ordered data mode. Opts: (null)
[ 38.753590] wm8804 1-003b: revision E
[ 38.759397] snd-hifiberry-digi soc:sound: wm8804-spdif <-> 20203000.i2s mapping ok
[ 46.093087] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0x45E1

Der Router (Fritzbox) vergibt auch korrekt die IP-Adresse und löst den Namen auf. Passt auch alles zur Ausgabe von ifconfig:

pi@Brain:~ $ ifconfig
eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 192.168.178.28 netmask 255.255.255.0 broadcast 192.168.178.255
ether b8:27:eb:12:7a:7b txqueuelen 1000 (Ethernet)
RX packets 670062 bytes 713194104 (680.1 MiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 811999 bytes 940860789 (897.2 MiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0

lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
loop txqueuelen 1000 (Local Loopback)
RX packets 304154 bytes 921591821 (878.8 MiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 304154 bytes 921591821 (878.8 MiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0

Wie gesagt, unter 192.168.178.28:9000 komme ich auch einwandfrei auf die LMS-Oberfläche. Bloß führen weder „brain“ noch 192.168.178.28 zur altgewohnten max2play Oberfläche. Bevor ich über die (dann noch vorhandene) max2play Oberfläche den LMS installiert und auf HifiBerry Digi umgestellt hatte, ging der Zugriff auch noch. Sound und LMS funktionieren gut. Bloß die Weboberfläche kommt nicht mehr rein.