Reply To: Hintergrundbeleuchtung 2.8" Display

20. März 2017 at 12:53 #27802

Hallo Heiner,
hier die anderen Debug-Infos:

———————————–
#### SQUEEZELITE VERSION ####
Squeezelite Max2Play v1.0.1 based on v1.8.4-726, Copyright 2012-2015 Adrian Smith, 2015-2016 Ralph Irving.
#### SQUEEZELITE BUILDOPTIONS ####
Build options: LINUX ALSA EVENTFD RESAMPLE FFMPEG VISEXPORT IR GPIO DSD CONTROLSBS ALSASYNC BLUETOOTHSYNC
#### AUDIOPLAYER CONFIG ####
### Configuration of Audioplayers
SQUEEZELITE_PARAMETER=-o sysdefault:CARD=sndrpihifiberry -a 80:4:: -o hw:0 -V Digital
SQUEEZESLAVE_PARAMETER=-n plugequal
SHAIRPORT_PARAMETER=-d default:CARD=sndrpihifiberry
USE_USB_DAC=0
USE_EQUALIZER=0
SYSTEM_USER=pi
YMPD_PARAMETER=–webport 8081
#### SQUEEZELITE -l ####
Output devices:
null – Discard all samples (playback) or generate zero samples (capture)
equal
plugequal – Equalizer for plughw:0,0
default:CARD=sndrpihifiberry – snd_rpi_hifiberry_dacplus, – Default Audio Device
sysdefault:CARD=sndrpihifiberry – snd_rpi_hifiberry_dacplus, – Default Audio Device
dmix:CARD=sndrpihifiberry,DEV=0 – snd_rpi_hifiberry_dacplus, – Direct sample mixing device
dsnoop:CARD=sndrpihifiberry,DEV=0 – snd_rpi_hifiberry_dacplus, – Direct sample snooping device
hw:CARD=sndrpihifiberry,DEV=0 – snd_rpi_hifiberry_dacplus, – Direct hardware device without any conversions
plughw:CARD=sndrpihifiberry,DEV=0 – snd_rpi_hifiberry_dacplus, – Hardware device with all software conversions
#### SHAIRPORT VERSION ####
2.8.0-openssl-Avahi-ALSA-soxr
#### OUTPUT SOUND DETAILS CARD 0 ####
closed
#### OUTPUT SOUND DETAILS CARD 1 ####
—–
eth0 Link encap:Ethernet HWaddr b8:27:eb:20:f3:87
inet addr:192.168.0.113 Bcast:192.168.0.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1026809 errors:0 dropped:46 overruns:0 frame:0
TX packets:699573 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:259338324 (247.3 MiB) TX bytes:49389429 (47.1 MiB)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:169179 errors:0 dropped:0 overruns:0 frame:0
TX packets:169179 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1
RX bytes:14828583 (14.1 MiB) TX bytes:14828583 (14.1 MiB)
wlan0 Link encap:Ethernet HWaddr b8:27:eb:75:a6:d2
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
—-
#### BOOT CONFIG TXT ####
# For more options and information see
# http://www.raspberrypi.org/documentation/configuration/config-txt.md
# Some settings may impact device functionality. See link above for details
# uncomment if you get no picture on HDMI for a default „safe“ mode
#hdmi_safe=1
# uncomment this if your display has a black border of unused pixels visible
# and your display can output without overscan
#disable_overscan=1
# uncomment the following to adjust overscan. Use positive numbers if console
# goes off screen, and negative if there is too much border
#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16
# uncomment to force a console size. By default it will be display’s size minus
# overscan.
#framebuffer_width=1280
#framebuffer_height=720
# uncomment if hdmi display is not detected and composite is being output
#hdmi_force_hotplug=1
# uncomment to force a specific HDMI mode (this will force VGA)
#hdmi_group=1
#hdmi_mode=1
# uncomment to force a HDMI mode rather than DVI. This can make audio work in
# DMT (computer monitor) modes
#hdmi_drive=2
# uncomment to increase signal to HDMI, if you have interference, blanking, or
# no display
#config_hdmi_boost=4
# uncomment for composite PAL
#sdtv_mode=2
#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=800
# Uncomment some or all of these to enable the optional hardware interfaces
#dtparam=i2c_arm=on
#dtparam=i2s=on
#dtparam=spi=on
# Uncomment this to enable the lirc-rpi module
#dtoverlay=lirc-rpi
# Additional overlays and parameters are documented /boot/overlays/README
# Enable audio (loads snd_bcm2835)
dtparam=audio=off
gpu_mem=128
dtoverlay=hifiberry-dacplus
max_usb_current=1
lcd_rotate=2
—-

Gruß Rainer