Reply To: [UPDATE] Bluetooth Addon BETA

Max2Play Home 2016 (en) Forums Max2Play Add-ons [UPDATE] Bluetooth Addon BETA Reply To: [UPDATE] Bluetooth Addon BETA

28. Dezember 2016 at 15:58 #25311

Following my earlier post I’ve reinstalled with current Jessie version (new card/fresh install) and done all updates etc. I’ve had more success with Bluetooth to a point in that packages seem to be installed, but still cannot connect to devices that are visible to other Bluetooth/eachother but not currently connected to anything (speaker and phone). No ‚known devices‘ section appears on the Bluetooth tab. Debug information below again showing nothing for dongle (but I am using RPI3 so no dongle attached, only built in Bluetooth – bought as RPI3 and detected as RPI3 by Max2Play). I also went in via terminal as user pi/sudo to check to see what was working in bluetooth – all packages seem to be installed and up to date and I have rebooted at least 3 times. I copied below bluetoothctl outputs which suggest no controller (list also blank)?? Any ideas? Google searches just suggest the packages etc which are already installed which I have checked with apt-get and they are definitely all installed.

*** BluetoothCTL commands ***

[bluetooth]# devices
[bluetooth]# power on
No default controller available
[bluetooth]# list
[bluetooth]#

*** BLUETOOTH DEBUG INFO ***
#### Bluetooth Installation ####

#### Bluetooth Dongle ####

#### PACMD LIST | grep active ####

SSH is enabled and the default password for the ‚pi‘ user has not been changed.
This is a security risk – please login as the ‚pi‘ user and type ‚passwd‘ to set a new password.

active port: <analog-output>
active profile: <output:analog-stereo>

#### PACMD LIST | grep sink ####

SSH is enabled and the default password for the ‚pi‘ user has not been changed.
This is a security risk – please login as the ‚pi‘ user and type ‚passwd‘ to set a new password.

Default sink name: alsa_output.0.analog-stereo
module.description = „When a bluetooth sink or source is added, load module-loopback“
module.description = „Automatically restore the default sink and source“
module.description = „When a sink/source is removed, try to move its streams to the default sink/source“
name: <module-always-sink>
module.description = „Always keeps at least one sink loaded even if it’s a null one“
module.description = „When a sink/source is idle for too long, suspend it“
module.description = „Load filter sinks automatically when needed“
1 sink(s) available.
sinks:
0 sink input(s) available.

#### X-SERVER RUNNING ####
1

#### PULSEAUDIO RUNNING ####
1 S 1000 1389 1 0 80 0 – 23636 – ? 00:00:00 pulseaudio
1 S 1000 1453 1 0 80 0 – 478 – ? 00:00:00 start-pulseaudi

*** SETTINGS/REBOOT DEBUG ALSO BELOW: – ***

#### FILESYSTEM ####
Filesystem 1K-blocks Used Available Use% Mounted on
/dev/root 7427824 2680568 4420892 38% /
devtmpfs 437056 0 437056 0% /dev
tmpfs 441388 68 441320 1% /dev/shm
tmpfs 441388 6192 435196 2% /run
tmpfs 5120 4 5116 1% /run/lock
tmpfs 441388 0 441388 0% /sys/fs/cgroup
/dev/mmcblk0p1 61384 21576 39808 36% /boot
tmpfs 88280 8 88272 1% /run/user/1000
192.168.1.220:/volume1/Music 2879621632 1956036096 923483136 68% /mnt/MusicDS

#### LOAD AVERAGE ####
0.00 0.02 0.03 1/210 6824

#### KERNEL ####
Linux ServerLounge 4.4.20-v7+ #908 SMP Wed Sep 7 14:44:27 BST 2016 armv7l GNU/Linux

#### LINUX-VERSION ####
Distributor ID: Raspbian
Description: Raspbian GNU/Linux 8.0 (jessie)
Release: 8.0
Codename: jessie