{"id":21797,"date":"2016-07-25T14:53:05","date_gmt":"2016-07-25T12:53:05","guid":{"rendered":"https:\/\/www.max2play.com\/?page_id=21797"},"modified":"2016-12-21T12:03:35","modified_gmt":"2016-12-21T10:03:35","slug":"assembly-instruction-hifiberry-amp-case-black","status":"publish","type":"page","link":"https:\/\/www.max2play.com\/en\/assembly-instruction-hifiberry-amp-case-black\/","title":{"rendered":"Assembly instruction HiFiBerry AMP+ Case (black)"},"content":{"rendered":"[spb_text_block pb_margin_bottom=&#8220;no&#8220; pb_border_bottom=&#8220;no&#8220; width=&#8220;1\/1&#8243; el_position=&#8220;first last&#8220;]\n<p>We will show you how to assemble the case for the Raspberry Pi 2 &amp; 3 and HiFiBerry AMP+ cards. It is a black case and you can buy it <a href=\"https:\/\/shop.max2play.com\/en\/zubehor\/case-gehaeuse\/case-amp.html\" target=\"_blank\">in our shop<\/a>.<\/p>\n[\/spb_text_block] [spb_text_block title=&#8220;Scope of delivery&#8220; pb_margin_bottom=&#8220;no&#8220; pb_border_bottom=&#8220;no&#8220; width=&#8220;2\/3&#8243; el_position=&#8220;first&#8220;]\n<ul>\n<li>Case for Raspberry Pi and HiFiBerry AMP+<\/li>\n<li>4x spacers (15mm)<\/li>\n<li>4x spacers (3mm)<\/li>\n<li>8x screws<\/li>\n<\/ul>\n<p>Is required in addition:<\/p>\n<ul>\n<li>Raspberry Pi 2 or 3<\/li>\n<li>HiFiBerry AMP+ (Included in delivery 4x plastic spacers (12mm)<\/li>\n<li>SD-Card with preinstalled Max2Play<\/li>\n<li>power supply for HiFiBerry AMP+<\/li>\n<\/ul>\n<p>&nbsp;<\/p>\n<p>Open the bags and unpack the parts. Make sure to remove the protective layer from the plates, they stick to the surface so try peeling them off on the edges. When you are done, your parts should look like the right image.<\/p>\n[\/spb_text_block] [spb_single_image image=&#8220;25072&#8243; image_size=&#8220;full&#8220; frame=&#8220;noframe&#8220; intro_animation=&#8220;none&#8220; full_width=&#8220;no&#8220; lightbox=&#8220;yes&#8220; link_target=&#8220;_self&#8220; width=&#8220;1\/3&#8243; el_position=&#8220;last&#8220;] [spb_column width=&#8220;1\/3&#8243; el_position=&#8220;first&#8220;] [spb_single_image image=&#8220;25073&#8243; image_size=&#8220;full&#8220; frame=&#8220;noframe&#8220; intro_animation=&#8220;none&#8220; full_width=&#8220;no&#8220; lightbox=&#8220;yes&#8220; link_target=&#8220;_self&#8220; width=&#8220;1\/1&#8243; el_position=&#8220;first last&#8220;] [spb_text_block title=&#8220;Step 1&#8243; pb_margin_bottom=&#8220;no&#8220; pb_border_bottom=&#8220;no&#8220; width=&#8220;1\/1&#8243; el_position=&#8220;first last&#8220;]\n<p>Take the bottom plate, four screws and the four spacers (3mm). Now carry the screws through the recesses of the floor plate. For comparison, in the right you can see a picture of how it should look.<\/p>\n[\/spb_text_block] [\/spb_column] [spb_column width=&#8220;1\/3&#8243;] [spb_single_image image=&#8220;25074&#8243; image_size=&#8220;full&#8220; frame=&#8220;noframe&#8220; intro_animation=&#8220;none&#8220; full_width=&#8220;no&#8220; lightbox=&#8220;yes&#8220; link_target=&#8220;_self&#8220; width=&#8220;1\/1&#8243; el_position=&#8220;first last&#8220;] [spb_text_block title=&#8220;Step 2&#8243; pb_margin_bottom=&#8220;no&#8220; pb_border_bottom=&#8220;no&#8220; width=&#8220;1\/1&#8243; el_position=&#8220;first last&#8220;]\n<p>Put the Raspberry Pi on the screws. Take the plastic spacers (12mm)\u00a0which were delievered with\u00a0the HiFiBerry AMP + sound card. Fix the Raspberry Pi with these spacers.<\/p>\n[\/spb_text_block] [\/spb_column] [spb_column width=&#8220;1\/3&#8243; el_position=&#8220;last&#8220;] [spb_single_image image=&#8220;25075&#8243; image_size=&#8220;full&#8220; frame=&#8220;noframe&#8220; intro_animation=&#8220;none&#8220; full_width=&#8220;no&#8220; lightbox=&#8220;yes&#8220; link_target=&#8220;_self&#8220; width=&#8220;1\/1&#8243; el_position=&#8220;first last&#8220;] [spb_text_block title=&#8220;Step 3&#8243; pb_margin_bottom=&#8220;no&#8220; pb_border_bottom=&#8220;no&#8220; width=&#8220;1\/1&#8243; el_position=&#8220;first last&#8220;]\n<p>Now\u00a0place\u00a0the HiFiBerry AMP+ on the pins of the Raspberry Pi. Take the metal spacers (15mm) and\u00a0attach the sound card.<\/p>\n[\/spb_text_block] [\/spb_column] [spb_single_image image=&#8220;25076&#8243; image_size=&#8220;full&#8220; frame=&#8220;noframe&#8220; intro_animation=&#8220;none&#8220; full_width=&#8220;no&#8220; lightbox=&#8220;yes&#8220; link_target=&#8220;_self&#8220; width=&#8220;1\/3&#8243; el_position=&#8220;first&#8220;] [spb_text_block title=&#8220;Step 4&#8243; pb_margin_bottom=&#8220;no&#8220; pb_border_bottom=&#8220;no&#8220; width=&#8220;2\/3&#8243; el_position=&#8220;last&#8220;]\n<p>Now, the first side part of the\u00a0Case have to be\u00a0attached. Take the side panel with the recesses for the connections of the Raspberry Pi and the HiFiBerry AMP+. Put it carefully, because the parts are fragile.<\/p>\n<p>Note: Now connect the passive boxes\u00a0with the sound card. This is the last possibility for this. After\u00a0closing the Case, there is no access to the locking screws of the HiFiBerry AMP+.<\/p>\n[\/spb_text_block] [spb_text_block title=&#8220;Step 5&#8243; pb_margin_bottom=&#8220;no&#8220; pb_border_bottom=&#8220;no&#8220; width=&#8220;2\/3&#8243; el_position=&#8220;first&#8220;]\n<p>Now\u00a0take the\u00a0rest of the side plates.\u00a0The side plates\u00a0can be simply placed on the floor plate.<\/p>\n<p>Note: The sides should fit easily into the gaps. Do not apply excessive pressure because\u00a0the small plastic parts are fragile.<\/p>\n<p>Take the cover plate with the HiFiBerry logo and place it on the side plates.<\/p>\n<p>Note: The holes for the screws should lie directly over the spacers.<\/p>\n<p>Finally, the four remaining screws are tightened. And the housing for the HiFiBerry AMP+ is ready.<\/p>\n[\/spb_text_block] [spb_single_image image=&#8220;25077&#8243; image_size=&#8220;full&#8220; frame=&#8220;noframe&#8220; intro_animation=&#8220;none&#8220; full_width=&#8220;no&#8220; lightbox=&#8220;yes&#8220; link_target=&#8220;_self&#8220; width=&#8220;1\/3&#8243; el_position=&#8220;last&#8220;] [spb_single_image image=&#8220;25079&#8243; image_size=&#8220;full&#8220; frame=&#8220;noframe&#8220; intro_animation=&#8220;none&#8220; full_width=&#8220;no&#8220; lightbox=&#8220;yes&#8220; link_target=&#8220;_self&#8220; width=&#8220;1\/2&#8243; el_position=&#8220;first&#8220;] [spb_single_image image=&#8220;25080&#8243; image_size=&#8220;full&#8220; frame=&#8220;noframe&#8220; intro_animation=&#8220;none&#8220; full_width=&#8220;no&#8220; lightbox=&#8220;yes&#8220; link_target=&#8220;_self&#8220; width=&#8220;1\/2&#8243; el_position=&#8220;last&#8220;] [spb_text_block title=&#8220;Interested in more&#8220; pb_margin_bottom=&#8220;no&#8220; pb_border_bottom=&#8220;no&#8220; width=&#8220;1\/1&#8243; el_position=&#8220;first last&#8220;]\n<p>You will find more assembly instructions here:<\/p>\n<a class=\"sf-button standard accent stroke-to-fill  dropshadow\" href=\"https:\/\/www.max2play.com\/en\/how-tos\/\" target=\"_blank\"><span class=\"text\">Max2Play How-To<\/span><\/a>\n[\/spb_text_block]\n","protected":false},"excerpt":{"rendered":"<p>[spb_text_block pb_margin_bottom=&#8220;no&#8220; pb_border_bottom=&#8220;no&#8220; width=&#8220;1\/1&#8243; el_position=&#8220;first last&#8220;] We will show you how to assemble the case for the Raspberry Pi 2 &amp; 3 and HiFiBerry AMP+ cards. It is a black case and you can buy it in our shop. [\/spb_text_block] [spb_text_block title=&#8220;Scope of delivery&#8220; pb_margin_bottom=&#8220;no&#8220; pb_border_bottom=&#8220;no&#8220; width=&#8220;2\/3&#8243; el_position=&#8220;first&#8220;] Case for Raspberry Pi and HiFiBerry AMP+ 4x spacers (15mm) 4x spacers [&hellip;]<\/p>\n","protected":false},"author":1316,"featured_media":0,"parent":0,"menu_order":0,"comment_status":"closed","ping_status":"closed","template":"","meta":{"_bbp_topic_count":0,"_bbp_reply_count":0,"_bbp_total_topic_count":0,"_bbp_total_reply_count":0,"_bbp_voice_count":0,"_bbp_anonymous_reply_count":0,"_bbp_topic_count_hidden":0,"_bbp_reply_count_hidden":0,"_bbp_forum_subforum_count":0},"aioseo_notices":[],"_links":{"self":[{"href":"https:\/\/www.max2play.com\/en\/wp-json\/wp\/v2\/pages\/21797"}],"collection":[{"href":"https:\/\/www.max2play.com\/en\/wp-json\/wp\/v2\/pages"}],"about":[{"href":"https:\/\/www.max2play.com\/en\/wp-json\/wp\/v2\/types\/page"}],"author":[{"embeddable":true,"href":"https:\/\/www.max2play.com\/en\/wp-json\/wp\/v2\/users\/1316"}],"replies":[{"embeddable":true,"href":"https:\/\/www.max2play.com\/en\/wp-json\/wp\/v2\/comments?post=21797"}],"version-history":[{"count":8,"href":"https:\/\/www.max2play.com\/en\/wp-json\/wp\/v2\/pages\/21797\/revisions"}],"predecessor-version":[{"id":25105,"href":"https:\/\/www.max2play.com\/en\/wp-json\/wp\/v2\/pages\/21797\/revisions\/25105"}],"wp:attachment":[{"href":"https:\/\/www.max2play.com\/en\/wp-json\/wp\/v2\/media?parent=21797"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}