[spb_column width=“1\/3″ el_position=“first“] [spb_single_image image=“21436″ image_size=“full“ frame=“noframe“ intro_animation=“none“ full_width=“no“ lightbox=“yes“ link_target=“_self“ width=“1\/1″ el_position=“first last“] [spb_text_block title=“Step 1″ pb_margin_bottom=“no“ pb_border_bottom=“no“ width=“1\/1″ el_position=“first last“]\n
We will now show you how to assemble the case for the IQaudIO sound cards.<\/p>\n
Unpack the components and remove the protection film on them. They are sticking on either side of the individual plates of the device. Check if all components are there, you can cross-reference them with the picture on the right.<\/p>\n[\/spb_text_block] [\/spb_column] [spb_column width=“1\/3″] [spb_single_image image=“21437″ image_size=“full“ frame=“noframe“ intro_animation=“none“ full_width=“no“ lightbox=“yes“ link_target=“_self“ width=“1\/1″ el_position=“first last“] [spb_text_block title=“Step 2″ pb_margin_bottom=“no“ pb_border_bottom=“no“ width=“1\/1″ el_position=“first last“]\n
Screw the spacers with the longer threads onto the Raspberry Pi (21mm spacers; see left picture).<\/p>\n[\/spb_text_block] [\/spb_column] [spb_column width=“1\/3″ el_position=“last“] [spb_single_image image=“21438″ image_size=“full“ frame=“noframe“ intro_animation=“none“ full_width=“no“ lightbox=“yes“ link_target=“_self“ width=“1\/1″ el_position=“first last“] [spb_text_block title=“Step 3″ pb_margin_bottom=“no“ pb_border_bottom=“no“ width=“1\/1″ el_position=“first last“]\n
Now place the IQaudIO sound card onto the pins of the Raspberry Pi to make the spacers fit into the holes of the sound card and mount it with the remaining spacers (24,5mm spacers; see right picture).<\/p>\n[\/spb_text_block] [\/spb_column] [spb_column width=“1\/1″ el_position=“first last“] [spb_single_image image=“23544″ image_size=“full“ frame=“noframe“ intro_animation=“none“ full_width=“no“ lightbox=“yes“ link_target=“_self“ width=“1\/4″ el_position=“first“] [spb_single_image image=“23548″ image_size=“full“ frame=“noframe“ intro_animation=“none“ full_width=“no“ lightbox=“yes“ link_target=“_self“ width=“1\/4″] [spb_text_block title=“Step 4″ pb_margin_bottom=“no“ pb_border_bottom=“no“ width=“1\/2″ el_position=“last“]\n
In this case, it is important to place the individual parts correctly into the recesses. You can use the following pictures. The parts can be arranged beforehand, as shown in the picture. There you can see the floor plate and the sides.<\/p>\n[\/spb_text_block] [\/spb_column] [spb_column width=“1\/1″ el_position=“first last“] [spb_single_image image=“21441″ image_size=“full“ frame=“noframe“ intro_animation=“none“ full_width=“no“ lightbox=“yes“ link_target=“_self“ width=“1\/4″ el_position=“first“] [spb_text_block title=“Step 5″ pb_margin_bottom=“no“ pb_border_bottom=“no“ width=“3\/4″ el_position=“last“]\n
In this step, the side panels are first attached to the device before assembling the case. A distinction must be made between IQaudIO DigiAMP+ and IQaudIO DAC+. There are different notches on the side panel for both sound cards. In this example, an IQaudIO DigiAMP+<\/strong> is used.<\/p>\n Attention:\u00a0<\/strong>It may be that there is an overhang on the board of IQaudIO. This must first be removed with sandpaper. Do this in a careful way and take only so much away that the page is on one level.<\/p>\n Now you can place the unit with the sides on the floor plate.<\/p>\n Before the roof plate is screwed to the case, the cables of the loudspeaker should be connected to the IQaudIO DigiAMP +. It is then no longer possible to tighten the screws of the IQaudIO DigiAMP+.<\/p>\n <\/p>\n[\/spb_text_block] [\/spb_column] [spb_text_block title=“Step 6″ pb_margin_bottom=“no“ pb_border_bottom=“no“ width=“3\/4″ el_position=“first“]\n In the last step, the floor and roof plate is screwed to the case. To avoid scratches on the base, rubber feet are included in the package. These can be attached to the protuberances of the screws outside the housing.<\/p>\n In the right picture you can see the case when it is assembled<\/p>\n[\/spb_text_block] [spb_single_image image=“21442″ image_size=“full“ frame=“noframe“ intro_animation=“none“ full_width=“no“ lightbox=“yes“ link_target=“_self“ width=“1\/4″ el_position=“last“] [spb_text_block title=“Interested in more“ pb_margin_bottom=“no“ pb_border_bottom=“no“ width=“1\/1″ el_position=“first last“]\n